WTC MUD #1 RecordsBoard minutes, agendas and votes

Park Pro Tek - Playscape Safety Inspections

Unofficial searchable copy. For the official record, use the district’s own copy.

Page 1

Cedar Park
08/07/2023
09:41 AM

Page 2

General Information
Company Name: Inframark
Property Manager: Makenzie Scales
Address: 2900 El Salido Parkway  
Email:
Phone Number: (713) 594-6335
Inspection by: Dustin Beber

Page 3

Table of Contents
Playground Location
Priority Glossary
Inspector Checklist
1: Playground Area- Anderson Mill West Park
1.1: General Playground Concerns
1.2: Age / Size Appropriateness Design
1.3: Playground Protective Surface
1.4: Slides
1.5: Climbing Equipment
1.6: Rotating and Rocking Equipment
1.7: Use Zone
1.8: Swings
2: Playground Area
2.1: General Playground Concerns
2.2: Age / Size Appropriateness Design
2.3: Playground Protective Surface
2.4: Slides
2.5: Climbing Equipment
2.6: Swings
2.7: Rotating and Rocking Equipment
2.8: Use Zone
3: Tennis Court
3.1: General

Page 4

4: Basketball Court
4.1: General
5: Volleyball Court
5.1: General
6: Playground Area - Lakeline Oak Park
6.1: General Playground Concerns
6.2: Age / Size Appropriateness Design
6.3: Climbing Equipment
6.4: Playground Protective Surface
6.5: Rotating and Rocking Equipment
6.6: Slides
6.7: Swings
6.8: Use Zone
7: Playground Area
7.1: General Playground Concerns
7.2: Age / Size Appropriateness Design
7.3: Climbing Equipment
7.4: Playground Protective Surface
7.5: Slides
7.6: Swings
7.7: Use Zone
8: Playground Area - Volente Hills Park
8.1: General Playground Concerns

Page 5

8.2: Age / Size Appropriateness Design
8.3: Climbing Equipment
8.4: Playground Protective Surface
8.5: Slides
8.6: Swings
8.7: Use Zone
9: Playground Area
9.1: General Playground Concerns
9.2: Age / Size Appropriateness Design
9.3: Climbing Equipment
9.4: Playground Protective Surface
9.5: Slides
9.6: Use Zone
10: Playground Area - Sun Chase
10.1: General Playground Concerns
10.2: Age / Size Appropriateness Design
10.3: Playground Protective Surface
10.4: Slides
10.5: Use Zone
11: Playground Area - Madeline Loop Pond
11.1: General Playground Concerns
12: Playground Area - Hatch Pond Park
12.1: General Playground Concerns
12.2: Age / Size Appropriateness Design

Page 6

12.3: Climbing Equipment
12.4: Playground Protective Surface
12.5: Use Zone
12.6: Swings
13: Playground Area - Anderson Mill Pond Park
13.1: Swings
Summary
Notes

Page 7

Playground Location
ParkPro Tek
Page 7 of 80

Page 8

Priority Glossary
One:
Non-compliant safety concern that may result in permanent disability, loss of life or body part.
Condition should be corrected immediately.
Two:
Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.
Three: Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.
Four:
Non-compliant safety concern whose potential to cause an injury is very minimal.
Condition should be corrected if it worsens.
Five:
The item has been determined to be compliant with the owner/operator’s operating policy and
standard of care.
Continued ongoing preventive maintenance is recommended.
Inspector Checklist
Walked all areas included on the report for any non-compliant issues and provided detailed documentation
1: Playground Area- Anderson Mill West Park
1.1: General Playground Concerns
Compliant 1.1.1. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
Compliant 1.1.2. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
ParkPro Tek
Page 8 of 80

Page 9

Non-Compliant 1.1.3. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
This is a priority Four issue. (Non-compliant safety concern whose potential to cause an injury is very minimal.
Condition should be corrected if it worsens.)
Playground is at 192'
F2049 - 8.3 - Level III the hazard is over 100 ft up to 200 ft from play equipment or its use zone
Compliant 1.1.4. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
Recommended 1.1.5. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 1.1.6. Poisonous plants are removed from the play area.
Compliant 1.1.7. The play area is free of inappropriate materials or chemicals.
Compliant 1.1.8. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
ParkPro Tek
Page 9 of 80

Page 10

Compliant 1.1.9. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges. There
are no open holes in equipment forming traps (e.g. at the ends of tubes). There are no pinch,
crush or shear points.
Non-Compliant 1.1.10. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Non-compliant hardware on blue slide
ASTM - 6.4 - There shall be no entanglement hazards on public play equipment.
ParkPro Tek
Page 10 of 80

Page 11

Non-Compliant 1.1.11. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
Rusting and peeling decks, missing equipment, missing caps
ParkPro Tek
Page 11 of 80

Page 12

Compliant 1.1.12. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
Compliant 1.1.13. Is shade provided over the playground area*
Compliant 1.1.14. The height of transfer platforms is between 11"-18"
Height at 13.5"
ParkPro Tek
Page 12 of 80

Page 13

1.2: Age / Size Appropriateness Design
Compliant 1.2.1. The play area has signs that inform users of intended user age group. (CPSC 2.2.6).
KDISCLOSURE- Stickers on the unit in place of the sign are acceptable but can be easily
removed which is why permanent signs are recommendedK
1.3: Playground Protective Surface
Non-Compliant 1.3.1. All elevated play equipment (slides, swings, bridges, seesaws, climbing apparatus,
etc.) has proper depth of impact-absorbing material underneath the structure. Refer to
CPSC and ASTM ?1487-07 and ASTM 1292-04 for speci&cations on conforming protective
surface type, critical fall heights and how far surfacing should extend from structure.
PARYPRO TEY CANNOT GUARANTEE SUR?ACING IS COMPLIANT WITHOUT SUR?ACE
IMPACT TESTING WHICH IS HIGHLK RECOMMENDED ?OR EVERK SITE
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Damaged rubber, loose Mll at 3"
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
CPSC - 2.4.2.1 - xubber surfacing has eHtensive cracking and missing sections and should be replaced as it
is not compliant which is a priority one liability
CPSC - 2.4.2.1 - xubber surfacing is in need of patch repairs
ParkPro Tek
Page 13 of 80

Page 14

Recommended 1.3.2. Surfaces are inspected at least monthly and raked to prevent them from becoming
packed down and to remove hidden hazards (e.g. littler, sharp objects, animal feces).
Compliant 1.3.3. Standing water is not found within any of the use zones.
Compliant 1.3.4. ?or Equipment installed after 1995, manufacturers sign attached to equipment stating
equipment must be installed over impact absorbing surface . (ASTM 14.4.1.3)
1.4: Slides
ParkPro Tek
Page 14 of 80

Page 15

Compliant 1.4.1. If the slide is made in several pieces, the slide surface has no gaps or rough edges at
the top of the slide or at section seams that could entangle clothing or trap foreign material
(CPSC 12.4.3, 12.4.4)
N/A 1.4.2. ?or slides 4 high or less and designed for 2-5 year olds, the slide exit height does not
exceed 11" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
Compliant 1.4.3. ?or slides greater than 4' high, designed for 5-12 year olds, the slide exit height is
between 7" and 15" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
Compliant 1.4.4. The slide is free of obstructions throughout the use zone.
ParkPro Tek
Page 15 of 80

Page 16

Compliant 1.4.5. If the slide is made in one unitary piece, the slide surface has no gaps or rough edges
throughout that could entangle clothing or trap foreign material (CPSC 12.4.3, 12.4.4)
1.5: Climbing Equipment
Compliant 1.5.1. ?lexible access equipment anchoring devices are below the base of the minimum
required depth of the protective surface. (CPSC 12.1.3, ASTM 7.2.2.2)
Compliant 1.5.2. Handrails and handholds stay in place when grasped.
ParkPro Tek
Page 16 of 80

Page 17

1.6: Rotating and Rocking Equipment
N/A 1.6.1. There is a minimum of 9" between the protective surface and the underside of a
merry-go-round platform with a maximum height of 4" for the platform surface. (CPSC
12.2, ASTM 8.8.1.2, 8.8.1.4)
Compliant 1.6.2. There are no accessible shearing or crushing mechanisms in the undercarriage of the
equipment, and the platform does not provide an oscillatory (up and down) motion. (CPSC
12.2, ASTM 8.8.1.5)
Compliant 1.6.3. ?ootrests stay in place and pass the protrusion test. (CPSC 12.5, ASTM 8.11.3)
Compliant 1.6.4. Handholds stay in place when grasped and pass the protrusion test. (CPSC 12.5, ASTM
8. 11.2)
1.7: Use Zone
Compliant 1.7.1. The use zone for stationary play equipment shall extend no less than 72 in. (1830 mm)
from all sides of the play structure.
ParkPro Tek
Page 17 of 80

Page 18

Compliant 1.7.2. There shall be a use zone for each play structure which shall consist of obstacle-free
surfacing that conforms to Speci&cation ?1292 appropriate for the fall height of the
equipment.
1.8: Swings
Non-Compliant 1.8.1. Hardware is compliant with no issues present.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Lissing and incorrectly installed hardware.
Compliant 1.8.2. Swing hangers are spaced wider than seats, not less than 20. ( ASTM 8.6.1.5)
Compliant 1.8.3. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Non-Compliant 1.8.4. Swing surfacing is in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
0oose Mll at I" in many locations
ParkPro Tek
Page 18 of 80

Page 19

Non-Compliant 1.8.5. Swing seats are in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Damaged and missing hardware. 8nstalled incorrectly creating entanglement
None - null - Strap seat is damaged and should be replaced
None - null - Bardware is damaged and should be replaced
Compliant 1.8.6. Swing hangers are spaced wider than seats, not less than 20". ( ASTM 8.6.1.5)
Compliant 1.8.7. Vertical distance is at least 16" between underside of occupied seat and protective
surface. (5-12 equipment-ASTM 8.6.2.5)
Compliant 1.8.8. Vertical distance is at least 12" between underside of occupied seat and protective
surface (2-5 Equipment-ASTM 8.6.2.5)
Compliant 1.8.9. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Compliant 1.8.10. Swings are located away from circulation paths (a distance at least equal to the
equipment use zone and an additional safety factor for circulation, with this area free of
any obstructions) and near the periphery of the playground.
ParkPro Tek
Page 19 of 80

Page 20

2: Playground Area
2.1: General Playground Concerns
Compliant 2.1.11. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
Compliant 2.1.12. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
Non-Compliant 2.1.13. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
x2"
F2049 - 8.3 - Level II the hazard is 30 ft up to 100 ft from play equipment or its use zone
Compliant 2.1.14. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
ParkPro Tek
Page 20 of 80

Page 21

Recommended 2.1.15. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 2.1.16. Poisonous plants are removed from the play area.
Compliant 2.1.17. The play area is free of inappropriate materials or chemicals.
Compliant 2.1.18. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
Compliant 2.1.19. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges. There
are no open holes in equipment forming traps (e.g. at the ends of tubes). There are no pinch,
crush or shear points.
Compliant 2.1.20. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
ParkPro Tek
Page 21 of 80

Page 22

Non-Compliant 2.1.21. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Pinch points on rubber 7e4 climber. Lissing equipment.
Compliant 2.1.22. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
Compliant 2.1.23. Is shade provided over the playground area*
Compliant 2.1.24. The height of transfer platforms is between 11"-18"
ParkPro Tek
Page 22 of 80

Page 23

2.2: Age / Size Appropriateness Design
Compliant 2.2.1. The play area has signs that inform users of intended user age group. (CPSC 2.2.6).
KDISCLOSURE- Stickers on the unit in place of the sign are acceptable but can be easily
removed which is why permanent signs are recommendedK
2.3: Playground Protective Surface
Non-Compliant 2.3.1. All elevated play equipment (slides, swings, bridges, seesaws, climbing apparatus,
etc.) has proper depth of impact-absorbing material underneath the structure. Refer to
CPSC and ASTM ?1487-07 and ASTM 1292-04 for speci&cations on conforming protective
surface type, critical fall heights and how far surfacing should extend from structure.
PARYPRO TEY CANNOT GUARANTEE SUR?ACING IS COMPLIANT WITHOUT SUR?ACE
IMPACT TESTING WHICH IS HIGHLK RECOMMENDED ?OR EVERK SITE
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
0oose Mll at 2.B5". Rubber surfacing has missing sections
CPSC - 2.4.2.1 - xubber surfacing has eHtensive cracking and missing sections and should be replaced as it
is not compliant which is a priority one liability
CPSC - 2.4.2.1 - xubber surfacing is in need of patch repairs
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
ParkPro Tek
Page 23 of 80

Page 24

Recommended 2.3.2. Surfaces are inspected at least monthly and raked to prevent them from becoming
packed down and to remove hidden hazards (e.g. littler, sharp objects, animal feces).
Compliant 2.3.3. Standing water is not found within any of the use zones.
N/A 2.3.4. ?or Equipment installed after 1995, manufacturers sign attached to equipment
stating equipment must be installed over impact absorbing surface . (ASTM 14.4.1.3)
2.4: Slides
N/A 2.4.1. If the slide is made in several pieces, the slide surface has no gaps or rough edges at
the top of the slide or at section seams that could entangle clothing or trap foreign material
(CPSC 12.4.3, 12.4.4)
Compliant 2.4.2. ?or slides 4 high or less and designed for 2-5 year olds, the slide exit height does not
exceed 11" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
ParkPro Tek
Page 24 of 80

Page 25

Compliant 2.4.3. ?or slides greater than 4' high, designed for 5-12 year olds, the slide exit height is
between 7" and 15" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
Compliant 2.4.4. The slide is free of obstructions throughout the use zone.
Compliant 2.4.5. If the slide is made in one unitary piece, the slide surface has no gaps or rough edges
throughout that could entangle clothing or trap foreign material (CPSC 12.4.3, 12.4.4)
2.5: Climbing Equipment
ParkPro Tek
Page 25 of 80

Page 26

Compliant 2.5.1. ?lexible access equipment anchoring devices are below the base of the minimum
required depth of the protective surface. (CPSC 12.1.3, ASTM 7.2.2.2)
Compliant 2.5.2. Handrails and handholds stay in place when grasped.
2.6: Swings
Non-Compliant 2.6.1. Hardware is compliant with no issues present.
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
Damaged sharp edges
ParkPro Tek
Page 26 of 80

Page 27

Compliant 2.6.2. Swing hangers are spaced wider than seats, not less than 20. ( ASTM 8.6.1.5)
Compliant 2.6.3. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Non-Compliant 2.6.4. Swing surfacing is in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Rubber damaged. 0oose Mll at z"
CPSC - 2.4.2.1 - xubber surfacing has eHtensive cracking and missing sections and should be replaced as it
is not compliant which is a priority one liability
CPSC - 2.4.2.1 - xubber surfacing is in need of patch repairs
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
Non-Compliant 2.6.5. Swing seats are in good condition.
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Eucket seats have rust and sharp edges
None - null - jucket seat is damaged and should be replaced
ParkPro Tek
Page 27 of 80

Page 28

Compliant 2.6.6. Swing hangers are spaced wider than seats, not less than 20". ( ASTM 8.6.1.5)
N/A 2.6.7. Vertical distance is at least 16" between underside of occupied seat and protective
surface. (5-12 equipment-ASTM 8.6.2.5)
Compliant 2.6.8. Vertical distance is at least 12" between underside of occupied seat and protective
surface (2-5 Equipment-ASTM 8.6.2.5)
Compliant 2.6.9. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Compliant 2.6.10. Swings are located away from circulation paths (a distance at least equal to the
equipment use zone and an additional safety factor for circulation, with this area free of
any obstructions) and near the periphery of the playground.
2.7: Rotating and Rocking Equipment
ParkPro Tek
Page 28 of 80

Page 29

N/A 2.7.1. There is a minimum of 9" between the protective surface and the underside of a
merry-go-round platform with a maximum height of 4" for the platform surface. (CPSC
12.2, ASTM 8.8.1.2, 8.8.1.4)
Compliant 2.7.2. There are no accessible shearing or crushing mechanisms in the undercarriage of the
equipment, and the platform does not provide an oscillatory (up and down) motion. (CPSC
12.2, ASTM 8.8.1.5)
Compliant 2.7.3. ?ootrests stay in place and pass the protrusion test. (CPSC 12.5, ASTM 8.11.3)
Compliant 2.7.4. Handholds stay in place when grasped and pass the protrusion test. (CPSC 12.5, ASTM
8. 11.2)
2.8: Use Zone
Non-Compliant 2.8.1. The use zone for stationary play equipment shall extend no less than 72 in. (1830 mm)
from all sides of the play structure.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Tree in use Sone. Needs to be 13'. Only at x'
ParkPro Tek
Page 29 of 80

Page 30

Compliant 2.8.2. There shall be a use zone for each play structure which shall consist of obstacle-free
surfacing that conforms to Speci&cation ?1292 appropriate for the fall height of the
equipment.
3: Tennis Court
3.1: General
Compliant 3.1.3. Are all nets, posts and hardware in good condition*
Compliant 3.1.4. Is windscreen in good condition*
Compliant 3.1.5. Is surfacing in good condition*
4: Basketball Court
4.1: General
N/A 4.1.6. Is windscreen in good condition*
Recommended 4.1.7. Are all nets, rims, backboards and posts in good condition*
Nets are damaged and need to be replaced.
Compliant 4.1.8. Is surfacing in good condition*
5: Volleyball Court
5.1: General
Compliant 5.1.9. Volleyball net is tight and in good condition*
N/A 5.1.10. Watering system is working*
Compliant 5.1.11. Are posts and hardware tight and secured*
ParkPro Tek
Page 30 of 80

Page 31

Recommended 5.1.12. Sand is level and at a adequate depth*
Overgrown not level
6: Playground Area - Lakeline Oak Park
6.1: General Playground Concerns
Compliant 6.1.13. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
Compliant 6.1.14. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
Compliant 6.1.15. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
Earrier present.
ParkPro Tek
Page 31 of 80

Page 32

Compliant 6.1.16. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
Recommended 6.1.17. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 6.1.18. Poisonous plants are removed from the play area.
Compliant 6.1.19. The play area is free of inappropriate materials or chemicals.
Compliant 6.1.20. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
ParkPro Tek
Page 32 of 80

Page 33

Compliant 6.1.21. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges. There
are no open holes in equipment forming traps (e.g. at the ends of tubes). There are no pinch,
crush or shear points.
Compliant 6.1.22. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
No entanglements present
ParkPro Tek
Page 33 of 80

Page 34

Recommended 6.1.23. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
Lissing pieces on panel
Compliant 6.1.24. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
Recommended 6.1.25. Is shade provided over the playground area*
Hole in shade.
Compliant 6.1.26. The height of transfer platforms is between 11"-18"
Height is at 13.5". This is compliant.
ParkPro Tek
Page 34 of 80

Page 35

6.2: Age / Size Appropriateness Design
Compliant 6.2.1. The play area has signs that inform users of intended user age group. (CPSC 2.2.6).
KDISCLOSURE- Stickers on the unit in place of the sign are acceptable but can be easily
removed which is why permanent signs are recommendedK
6.3: Climbing Equipment
N/A 6.3.1. ?lexible access equipment anchoring devices are below the base of the minimum
required depth of the protective surface. (CPSC 12.1.3, ASTM 7.2.2.2)
Compliant 6.3.2. Handrails and handholds stay in place when grasped.
ParkPro Tek
Page 35 of 80

Page 36

6.4: Playground Protective Surface
Non-Compliant 6.4.1. All elevated play equipment (slides, swings, bridges, seesaws, climbing apparatus,
etc.) has proper depth of impact-absorbing material underneath the structure. Refer to
CPSC and ASTM ?1487-07 and ASTM 1292-04 for speci&cations on conforming protective
surface type, critical fall heights and how far surfacing should extend from structure.
PARYPRO TEY CANNOT GUARANTEE SUR?ACING IS COMPLIANT WITHOUT SUR?ACE
IMPACT TESTING WHICH IS HIGHLK RECOMMENDED ?OR EVERK SITE
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Rubber damaged. 0oose Mll at 3"
CPSC - 2.4.2.1 - xubber surfacing is in need of patch repairs
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
Recommended 6.4.2. Surfaces are inspected at least monthly and raked to prevent them from becoming
packed down and to remove hidden hazards (e.g. littler, sharp objects, animal feces).
Compliant 6.4.3. Standing water is not found within any of the use zones.
N/A 6.4.4. ?or Equipment installed after 1995, manufacturers sign attached to equipment
stating equipment must be installed over impact absorbing surface . (ASTM 14.4.1.3)
ParkPro Tek
Page 36 of 80

Page 37

6.5: Rotating and Rocking Equipment
N/A 6.5.1. There is a minimum of 9" between the protective surface and the underside of a
merry-go-round platform with a maximum height of 4" for the platform surface. (CPSC
12.2, ASTM 8.8.1.2, 8.8.1.4)
Compliant 6.5.2. There are no accessible shearing or crushing mechanisms in the undercarriage of the
equipment, and the platform does not provide an oscillatory (up and down) motion. (CPSC
12.2, ASTM 8.8.1.5)
Compliant 6.5.3. ?ootrests stay in place and pass the protrusion test. (CPSC 12.5, ASTM 8.11.3)
Compliant 6.5.4. Handholds stay in place when grasped and pass the protrusion test. (CPSC 12.5, ASTM
8. 11.2)
6.6: Slides
N/A 6.6.1. If the slide is made in several pieces, the slide surface has no gaps or rough edges at
the top of the slide or at section seams that could entangle clothing or trap foreign material
(CPSC 12.4.3, 12.4.4)
N/A 6.6.2. ?or slides 4 high or less and designed for 2-5 year olds, the slide exit height does not
exceed 11" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
Compliant 6.6.3. ?or slides greater than 4' high, designed for 5-12 year olds, the slide exit height is
between 7" and 15" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
ParkPro Tek
Page 37 of 80

Page 38

Compliant 6.6.4. The slide is free of obstructions throughout the use zone.
Compliant 6.6.5. If the slide is made in one unitary piece, the slide surface has no gaps or rough edges
throughout that could entangle clothing or trap foreign material (CPSC 12.4.3, 12.4.4)
6.7: Swings
Non-Compliant 6.7.1. Hardware is compliant with no issues present.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Hangers showing signs of e4treme wear and needs replacement.
ParkPro Tek
Page 38 of 80

Page 39

Compliant 6.7.2. Swing hangers are spaced wider than seats, not less than 20. ( ASTM 8.6.1.5)
Compliant 6.7.3. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Non-Compliant 6.7.4. Swing surfacing is in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
0oose Mll ranges from 2-z" and rubber has cracks
CPSC - 2.4.2.1 - xubber surfacing should have a maintenance urethane seal done to ensure longevity of the
pad
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
CPSC - 2.4.2.1 - xubber surfacing is in need of patch repairs
Compliant 6.7.5. Swing seats are in good condition.
Compliant 6.7.6. Swing hangers are spaced wider than seats, not less than 20". ( ASTM 8.6.1.5)
ParkPro Tek
Page 39 of 80

Page 40

Compliant 6.7.7. Vertical distance is at least 16" between underside of occupied seat and protective
surface. (5-12 equipment-ASTM 8.6.2.5)
Compliant 6.7.8. Vertical distance is at least 12" between underside of occupied seat and protective
surface (2-5 Equipment-ASTM 8.6.2.5)
Compliant 6.7.9. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Compliant 6.7.10. Swings are located away from circulation paths (a distance at least equal to the
equipment use zone and an additional safety factor for circulation, with this area free of
any obstructions) and near the periphery of the playground.
6.8: Use Zone
Compliant 6.8.1. The use zone for stationary play equipment shall extend no less than 72 in. (1830 mm)
from all sides of the play structure.
Compliant 6.8.2. There shall be a use zone for each play structure which shall consist of obstacle-free
surfacing that conforms to Speci&cation ?1292 appropriate for the fall height of the
equipment.
ParkPro Tek
Page 40 of 80

Page 41

7: Playground Area
7.1: General Playground Concerns
Compliant 7.1.3. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
Compliant 7.1.4. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
Non-Compliant 7.1.5. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Road at 155'
F2049 - 8.3 - Level III the hazard is over 100 ft up to 200 ft from play equipment or its use zone
Compliant 7.1.6. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
ParkPro Tek
Page 41 of 80

Page 42

Recommended 7.1.7. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 7.1.8. Poisonous plants are removed from the play area.
Compliant 7.1.9. The play area is free of inappropriate materials or chemicals.
Compliant 7.1.10. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
Compliant 7.1.11. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges. There
are no open holes in equipment forming traps (e.g. at the ends of tubes). There are no pinch,
crush or shear points.
Compliant 7.1.12. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
ParkPro Tek
Page 42 of 80

Page 43

Compliant 7.1.13. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
Compliant 7.1.14. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
Compliant 7.1.15. Is shade provided over the playground area*
Compliant 7.1.16. The height of transfer platforms is between 11"-18"
7.2: Age / Size Appropriateness Design
ParkPro Tek
Page 43 of 80

Page 44

Compliant 7.2.1. The play area has signs that inform users of intended user age group. (CPSC 2.2.6).
KDISCLOSURE- Stickers on the unit in place of the sign are acceptable but can be easily
removed which is why permanent signs are recommendedK
7.3: Climbing Equipment
N/A 7.3.1. ?lexible access equipment anchoring devices are below the base of the minimum
required depth of the protective surface. (CPSC 12.1.3, ASTM 7.2.2.2)
Non-Compliant 7.3.2. Handrails and handholds stay in place when grasped.
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Pinch points on rubber 7e4 climber
None - null - Bandhold is damaged and should be replaced
7.4: Playground Protective Surface
ParkPro Tek
Page 44 of 80

Page 45

Non-Compliant 7.4.1. All elevated play equipment (slides, swings, bridges, seesaws, climbing apparatus,
etc.) has proper depth of impact-absorbing material underneath the structure. Refer to
CPSC and ASTM ?1487-07 and ASTM 1292-04 for speci&cations on conforming protective
surface type, critical fall heights and how far surfacing should extend from structure.
PARYPRO TEY CANNOT GUARANTEE SUR?ACING IS COMPLIANT WITHOUT SUR?ACE
IMPACT TESTING WHICH IS HIGHLK RECOMMENDED ?OR EVERK SITE
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
Rubber damaged. 0oose Mll at 5"
Recommended 7.4.2. Surfaces are inspected at least monthly and raked to prevent them from becoming
packed down and to remove hidden hazards (e.g. littler, sharp objects, animal feces).
Compliant 7.4.3. Standing water is not found within any of the use zones.
Compliant 7.4.4. ?or Equipment installed after 1995, manufacturers sign attached to equipment
stating equipment must be installed over impact absorbing surface . (ASTM 14.4.1.3)
7.5: Slides
Compliant 7.5.1. If the slide is made in several pieces, the slide surface has no gaps or rough edges at
the top of the slide or at section seams that could entangle clothing or trap foreign material
(CPSC 12.4.3, 12.4.4)
N/A 7.5.2. ?or slides 4 high or less and designed for 2-5 year olds, the slide exit height does not
exceed 11" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
Compliant 7.5.3. ?or slides greater than 4' high, designed for 5-12 year olds, the slide exit height is
between 7" and 15" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
ParkPro Tek
Page 45 of 80

Page 46

Compliant 7.5.4. The slide is free of obstructions throughout the use zone.
Compliant 7.5.5. If the slide is made in one unitary piece, the slide surface has no gaps or rough edges
throughout that could entangle clothing or trap foreign material (CPSC 12.4.3, 12.4.4)
7.6: Swings
N/A 7.6.1. Hardware is compliant with no issues present.
N/A 7.6.2. Swing hangers are spaced wider than seats, not less than 20. ( ASTM 8.6.1.5)
N/A 7.6.3. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
N/A 7.6.4. Swing surfacing is in good condition.
N/A 7.6.5. Swing seats are in good condition.
Non-Compliant 7.6.6. Hardware is compliant with no issues present.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
G4treme wear on hangers and need replacement
ParkPro Tek
Page 46 of 80

Page 47

N/A 7.6.7. Swing hangers are spaced wider than seats, not less than 20". ( ASTM 8.6.1.5)
N/A 7.6.8. Swing hangers are spaced wider than seats, not less than 20. ( ASTM 8.6.1.5)
Compliant 7.6.9. Vertical distance is at least 16" between underside of occupied seat and protective
surface. (5-12 equipment-ASTM 8.6.2.5)
Compliant 7.6.10. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
N/A 7.6.11. Vertical distance is at least 12" between underside of occupied seat and protective
surface (2-5 Equipment-ASTM 8.6.2.5)
Non-Compliant 7.6.12. Swing surfacing is in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
0oose Mll at 3.B5". Rubber surfacing has missing sections
CPSC - 2.4.2.1 - xubber surfacing is in need of patch repairs
CPSC - 2.4 - The surfacing under and around playground equipment is one of the most important factors
in reducing the likelihood of life
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
ParkPro Tek
Page 47 of 80

Page 48

Compliant 7.6.13. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Non-Compliant 7.6.14. Swing seats are in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Lissing seat
Compliant 7.6.15. Swings are located away from circulation paths (a distance at least equal to the
equipment use zone and an additional safety factor for circulation, with this area free of
any obstructions) and near the periphery of the playground.
Non-Compliant 7.6.16. Swing hangers are spaced wider than seats, not less than 20". ( ASTM 8.6.1.5)
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Chains too close together
ParkPro Tek
Page 48 of 80

Page 49

Compliant 7.6.17. Vertical distance is at least 16" between underside of occupied seat and protective
surface. (5-12 equipment-ASTM 8.6.2.5)
N/A 7.6.18. Vertical distance is at least 12" between underside of occupied seat and protective
surface (2-5 Equipment-ASTM 8.6.2.5)
Compliant 7.6.19. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Compliant 7.6.20. Swings are located away from circulation paths (a distance at least equal to the
equipment use zone and an additional safety factor for circulation, with this area free of
any obstructions) and near the periphery of the playground.
7.7: Use Zone
Compliant 7.7.1. The use zone for stationary play equipment shall extend no less than 72 in. (1830 mm)
from all sides of the play structure.
Compliant 7.7.2. There shall be a use zone for each play structure which shall consist of obstacle-free
surfacing that conforms to Speci&cation ?1292 appropriate for the fall height of the
equipment.
8: Playground Area - Volente Hills Park
8.1: General Playground Concerns
Compliant 8.1.3. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
ParkPro Tek
Page 49 of 80

Page 50

Compliant 8.1.4. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
N/A 8.1.5. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
Compliant 8.1.6. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
Compliant 8.1.7. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 8.1.8. Poisonous plants are removed from the play area.
Compliant 8.1.9. The play area is free of inappropriate materials or chemicals.
Compliant 8.1.10. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
Compliant 8.1.11. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges. There
are no open holes in equipment forming traps (e.g. at the ends of tubes). There are no pinch,
crush or shear points.
ParkPro Tek
Page 50 of 80

Page 51

Compliant 8.1.12. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
Non-Compliant 8.1.13. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
0oose equipment. Eroken bubble panel. Rusted deck e4posing metal.
ParkPro Tek
Page 51 of 80

Page 52

Compliant 8.1.14. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
Recommended 8.1.15. Is shade provided over the playground area*
None - null - xecommended to keep playground from reaching eHtreme heat in the summer
Non-Compliant 8.1.16. The height of transfer platforms is between 11"-18"
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Transfer station at 21"
ParkPro Tek
Page 52 of 80

Page 53

8.2: Age / Size Appropriateness Design
Compliant 8.2.1. The play area has signs that inform users of intended user age group. (CPSC 2.2.6).
KDISCLOSURE- Stickers on the unit in place of the sign are acceptable but can be easily
removed which is why permanent signs are recommendedK
8.3: Climbing Equipment
N/A 8.3.1. ?lexible access equipment anchoring devices are below the base of the minimum
required depth of the protective surface. (CPSC 12.1.3, ASTM 7.2.2.2)
Non-Compliant 8.3.2. Handrails and handholds stay in place when grasped.
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
0oose equipment
8.4: Playground Protective Surface
ParkPro Tek
Page 53 of 80

Page 54

Non-Compliant 8.4.1. All elevated play equipment (slides, swings, bridges, seesaws, climbing apparatus,
etc.) has proper depth of impact-absorbing material underneath the structure. Refer to
CPSC and ASTM ?1487-07 and ASTM 1292-04 for speci&cations on conforming protective
surface type, critical fall heights and how far surfacing should extend from structure.
PARYPRO TEY CANNOT GUARANTEE SUR?ACING IS COMPLIANT WITHOUT SUR?ACE
IMPACT TESTING WHICH IS HIGHLK RECOMMENDED ?OR EVERK SITE
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
0oose Mll at I" in many locations
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
CPSC - 2.4 - The surfacing under and around playground equipment is one of the most important factors
in reducing the likelihood of life-threatening head in/uries
Recommended 8.4.2. Surfaces are inspected at least monthly and raked to prevent them from becoming
packed down and to remove hidden hazards (e.g. littler, sharp objects, animal feces).
Compliant 8.4.3. Standing water is not found within any of the use zones.
Compliant 8.4.4. ?or Equipment installed after 1995, manufacturers sign attached to equipment
stating equipment must be installed over impact absorbing surface . (ASTM 14.4.1.3)
8.5: Slides
N/A 8.5.1. If the slide is made in several pieces, the slide surface has no gaps or rough edges at
the top of the slide or at section seams that could entangle clothing or trap foreign material
(CPSC 12.4.3, 12.4.4)
N/A 8.5.2. ?or slides 4 high or less and designed for 2-5 year olds, the slide exit height does not
exceed 11" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
ParkPro Tek
Page 54 of 80

Page 55

Non-Compliant 8.5.3. ?or slides greater than 4' high, designed for 5-12 year olds, the slide exit height is
between 7" and 15" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
Wlide height at 22"
None - null - The slide height is too high but reRlling the proper surfacing will RH this issue
Compliant 8.5.4. The slide is free of obstructions throughout the use zone.
Compliant 8.5.5. If the slide is made in one unitary piece, the slide surface has no gaps or rough edges
throughout that could entangle clothing or trap foreign material (CPSC 12.4.3, 12.4.4)
8.6: Swings
N/A 8.6.1. Hardware is compliant with no issues present.
Compliant 8.6.2. Swing hangers are spaced wider than seats, not less than 20. ( ASTM 8.6.1.5)
N/A 8.6.3. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Non-Compliant 8.6.4. Swing surfacing is in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Wurfacing is at Sero in many locations.
ParkPro Tek
Page 55 of 80

Page 56

Non-Compliant 8.6.5. Swing seats are in good condition.
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
Eelt seats have sharp metal. Need replacement.
Compliant 8.6.6. Swing hangers are spaced wider than seats, not less than 20". ( ASTM 8.6.1.5)
Compliant 8.6.7. Vertical distance is at least 16" between underside of occupied seat and protective
surface. (5-12 equipment-ASTM 8.6.2.5)
Compliant 8.6.8. Vertical distance is at least 12" between underside of occupied seat and protective
surface (2-5 Equipment-ASTM 8.6.2.5)
Compliant 8.6.9. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
ParkPro Tek
Page 56 of 80

Page 57

Compliant 8.6.10. Swings are located away from circulation paths (a distance at least equal to the
equipment use zone and an additional safety factor for circulation, with this area free of
any obstructions) and near the periphery of the playground.
8.7: Use Zone
Compliant 8.7.1. The use zone for stationary play equipment shall extend no less than 72 in. (1830 mm)
from all sides of the play structure.
Compliant 8.7.2. There shall be a use zone for each play structure which shall consist of obstacle-free
surfacing that conforms to Speci&cation ?1292 appropriate for the fall height of the
equipment.
9: Playground Area
9.1: General Playground Concerns
Compliant 9.1.3. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
Compliant 9.1.4. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
N/A 9.1.5. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
Compliant 9.1.6. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
ParkPro Tek
Page 57 of 80

Page 58

N/A 9.1.7. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 9.1.8. Poisonous plants are removed from the play area.
Recommended 9.1.9. The play area is free of inappropriate materials or chemicals.
This is a priority Four issue. (Non-compliant safety concern whose potential to cause an injury is very minimal.
Condition should be corrected if it worsens.)
/raZti on independent slide in two locations.
Compliant 9.1.10. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
This is a priority Four issue. (Non-compliant safety concern whose potential to cause an injury is very minimal.
Condition should be corrected if it worsens.)
Compliant 9.1.11. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges. There
are no open holes in equipment forming traps (e.g. at the ends of tubes). There are no pinch,
crush or shear points.
ParkPro Tek
Page 58 of 80

Page 59

Compliant 9.1.12. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
Non-Compliant 9.1.13. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Damaged rope needs replacement.
Compliant 9.1.14. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
Recommended 9.1.15. Is shade provided over the playground area*
None - null - xecommended to keep playground from reaching eHtreme heat in the summer
ParkPro Tek
Page 59 of 80

Page 60

N/A 9.1.16. The height of transfer platforms is between 11"-18"
9.2: Age / Size Appropriateness Design
Compliant 9.2.1. The play area has signs that inform users of intended user age group. (CPSC 2.2.6).
KDISCLOSURE- Stickers on the unit in place of the sign are acceptable but can be easily
removed which is why permanent signs are recommendedK
9.3: Climbing Equipment
Compliant 9.3.1. ?lexible access equipment anchoring devices are below the base of the minimum
required depth of the protective surface. (CPSC 12.1.3, ASTM 7.2.2.2)
ParkPro Tek
Page 60 of 80

Page 61

Compliant 9.3.2. Handrails and handholds stay in place when grasped.
9.4: Playground Protective Surface
Non-Compliant 9.4.1. All elevated play equipment (slides, swings, bridges, seesaws, climbing apparatus,
etc.) has proper depth of impact-absorbing material underneath the structure. Refer to
CPSC and ASTM ?1487-07 and ASTM 1292-04 for speci&cations on conforming protective
surface type, critical fall heights and how far surfacing should extend from structure.
PARYPRO TEY CANNOT GUARANTEE SUR?ACING IS COMPLIANT WITHOUT SUR?ACE
IMPACT TESTING WHICH IS HIGHLK RECOMMENDED ?OR EVERK SITE
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Wurfacing at 3"
Recommended 9.4.2. Surfaces are inspected at least monthly and raked to prevent them from becoming
packed down and to remove hidden hazards (e.g. littler, sharp objects, animal feces).
Compliant 9.4.3. Standing water is not found within any of the use zones.
Compliant 9.4.4. ?or Equipment installed after 1995, manufacturers sign attached to equipment
stating equipment must be installed over impact absorbing surface . (ASTM 14.4.1.3)
9.5: Slides
Compliant 9.5.1. If the slide is made in several pieces, the slide surface has no gaps or rough edges at
the top of the slide or at section seams that could entangle clothing or trap foreign material
(CPSC 12.4.3, 12.4.4)
ParkPro Tek
Page 61 of 80

Page 62

N/A 9.5.2. ?or slides 4 high or less and designed for 2-5 year olds, the slide exit height does not
exceed 11" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
Non-Compliant 9.5.3. ?or slides greater than 4' high, designed for 5-12 year olds, the slide exit height is
between 7" and 15" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
Connected slide is at 2I"
Compliant 9.5.4. The slide is free of obstructions throughout the use zone.
Compliant 9.5.5. If the slide is made in one unitary piece, the slide surface has no gaps or rough edges
throughout that could entangle clothing or trap foreign material (CPSC 12.4.3, 12.4.4)
9.6: Use Zone
Compliant 9.6.1. The use zone for stationary play equipment shall extend no less than 72 in. (1830 mm)
from all sides of the play structure.
Compliant 9.6.2. There shall be a use zone for each play structure which shall consist of obstacle-free
surfacing that conforms to Speci&cation ?1292 appropriate for the fall height of the
equipment.
10: Playground Area - Sun Chase
10.1: General Playground Concerns
Compliant 10.1.3. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
ParkPro Tek
Page 62 of 80

Page 63

Recommended 10.1.4. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
Wome of the parts do not seem commercially safe. @ould need to see the install documents to ensure safety.
Non-Compliant 10.1.5. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
Playground less than 1II' from road.
F2049 - 1 - Standard guide for Fences,jarriers for public( commercial( and multi-family residential use
outdoor play areas
F2049 - 8.3 - Level II the hazard is 30 ft up to 100 ft from play equipment or its use zone
F2049 - 1.3 - This speciRcation does not choose the product components for the fence system( the choice
of which should be made by the operators of the play space and their speciRcation writers or drafters based
upon their determination of the merits of the products that could be used.
Recommended 10.1.6. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
Recommended 10.1.7. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 10.1.8. Poisonous plants are removed from the play area.
Compliant 10.1.9. The play area is free of inappropriate materials or chemicals.
Compliant 10.1.10. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
ParkPro Tek
Page 63 of 80

Page 64

Compliant 10.1.11. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges.
There are no open holes in equipment forming traps (e.g. at the ends of tubes). There are
no pinch, crush or shear points.
Non-Compliant 10.1.12. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Gntanglement and entrapment haSards on both stairs. Railing has an entrapment haSard.
ASTM - 6.4 - There shall be no entanglement hazards on public play equipment.
ParkPro Tek
Page 64 of 80

Page 65

Non-Compliant 10.1.13. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Eoth sets of stairs show minimal support and are loose. Play feature is not set in ground. DamagedAloose pole.
Compliant 10.1.14. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
ParkPro Tek
Page 65 of 80

Page 66

Compliant 10.1.15. Is shade provided over the playground area*
N/A 10.1.16. The height of transfer platforms is between 11"-18"
10.2: Age / Size Appropriateness Design
Recommended 10.2.1. The play area has signs that inform users of intended user age group. (CPSC 2.2.6).
KDISCLOSURE- Stickers on the unit in place of the sign are acceptable but can be easily
removed which is why permanent signs are recommendedK
10.3: Playground Protective Surface
Compliant 10.3.1. All elevated play equipment (slides, swings, bridges, seesaws, climbing apparatus,
etc.) has proper depth of impact-absorbing material underneath the structure. Refer to
CPSC and ASTM ?1487-07 and ASTM 1292-04 for speci&cations on conforming protective
surface type, critical fall heights and how far surfacing should extend from structure.
PARYPRO TEY CANNOT GUARANTEE SUR?ACING IS COMPLIANT WITHOUT SUR?ACE
IMPACT TESTING WHICH IS HIGHLK RECOMMENDED ?OR EVERK SITE
Wurfacing at 1I.5"
Recommended 10.3.2. Surfaces are inspected at least monthly and raked to prevent them from becoming
packed down and to remove hidden hazards (e.g. littler, sharp objects, animal feces).
ParkPro Tek
Page 66 of 80

Page 67

Compliant 10.3.3. Standing water is not found within any of the use zones.
Compliant 10.3.4. ?or Equipment installed after 1995, manufacturers sign attached to equipment
stating equipment must be installed over impact absorbing surface . (ASTM 14.4.1.3)
10.4: Slides
N/A 10.4.1. If the slide is made in several pieces, the slide surface has no gaps or rough edges at
the top of the slide or at section seams that could entangle clothing or trap foreign material
(CPSC 12.4.3, 12.4.4)
N/A 10.4.2. ?or slides 4 high or less and designed for 2-5 year olds, the slide exit height does not
exceed 11" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
Compliant 10.4.3. ?or slides greater than 4' high, designed for 5-12 year olds, the slide exit height is
between 7" and 15" above the protective surfacing material. (ASTM 8.5.5.3 CPSC 12.4.5)
Non-Compliant 10.4.4. The slide is free of obstructions throughout the use zone.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Railing is in the use Sone of the slides.
ParkPro Tek
Page 67 of 80

Page 68

Compliant 10.4.5. If the slide is made in one unitary piece, the slide surface has no gaps or rough edges
throughout that could entangle clothing or trap foreign material (CPSC 12.4.3, 12.4.4)
10.5: Use Zone
Compliant 10.5.1. The use zone for stationary play equipment shall extend no less than 72 in. (1830
mm) from all sides of the play structure.
Compliant 10.5.2. There shall be a use zone for each play structure which shall consist of obstacle-free
surfacing that conforms to Speci&cation ?1292 appropriate for the fall height of the
equipment.
11: Playground Area - Madeline Loop Pond
11.1: General Playground Concerns
Compliant 11.1.3. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
Compliant 11.1.4. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
ParkPro Tek
Page 68 of 80

Page 69

N/A 11.1.5. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
Compliant 11.1.6. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
N/A 11.1.7. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 11.1.8. Poisonous plants are removed from the play area.
Compliant 11.1.9. The play area is free of inappropriate materials or chemicals.
Compliant 11.1.10. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
Compliant 11.1.11. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges. There
are no open holes in equipment forming traps (e.g. at the ends of tubes). There are no pinch,
crush or shear points.
Compliant 11.1.12. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
ParkPro Tek
Page 69 of 80

Page 70

Compliant 11.1.13. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
Compliant 11.1.14. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
ParkPro Tek
Page 70 of 80

Page 71

Compliant 11.1.15. Is shade provided over the playground area*
N/A 11.1.16. The height of transfer platforms is between 11"-18"
12: Playground Area - Hatch Pond Park
12.1: General Playground Concerns
Compliant 12.1.17. The playground can be accessed safely by a sidewalk that is free of standing water,
sand, pea gravel and low (7'-0" minimum) hanging branches.
Compliant 12.1.18. Playground has only manufacturer approved parts and pieces unless speci&cally
documented by orignal manufacturer.
Compliant 12.1.19. If needed, suitable barrier (fence) is provided for border concerns within 200' of
playground edge
ParkPro Tek
Page 71 of 80

Page 72

Recommended 12.1.20. Signs give information about regulations on the use of the playground (hours, pets,
speci&c rules, etc.), name F phone number of playground owner (to report problems). Age
appropriateness of equipment. (CPSC 2.2.6)
N/A 12.1.21. Signs on all bordering roads advise motorists that a playground is nearby.
Compliant 12.1.22. Poisonous plants are removed from the play area.
Compliant 12.1.23. The play area is free of inappropriate materials or chemicals.
Compliant 12.1.24. The play area is visible to deter inappropriate behavior. (CPSC 2.2.5)
Compliant 12.1.25. Crush and shear points: (CSPS 3.1, ASTM 6.2). Equipment is free of sharp edges.
There are no open holes in equipment forming traps (e.g. at the ends of tubes). There are
no pinch, crush or shear points.
Compliant 12.1.26. Entanglement / entrapment angles (CPSC 3.2, ASTM 6.4): No more than two threads
of the fastener protrude through any nut. No obstacles for protrusions project upwards
from a horizontal plane extending more than 1/8" perpendicular to the plane of the initial
surface. There are no open "v" entrapment angles on any part of the equipment.There are
no gaps wider than1.8" that woud be cause for an entanglement hazard on any downward
sloping play equipment.
ParkPro Tek
Page 72 of 80

Page 73

Compliant 12.1.27. Hardware: Nuts and bolts are tight and not able to be loosened without tools. Upon
close inspection, they show no loose play or excessive wear (CPSC 2.5.2). Equipment is
free of rust and chipping paint. Equipment is free of sharp no loose play or excessive wear
(CPSC 2.5.2). Equipment is free of rust and chipping paint. Equipment is free of sharp edges,
splinters or rough surfaces and show no excessive wear. Ropes, chains,and cables have
not frayed or worn out. Equipment has not shifted or become bent. There is no corrosion
or visible rotting at points where equipment comes into contact with ground surface
(CPSC 7.2, 8.1) No components are missing. All parts of the equipment are present and in
good working order with no loose play or excessive wear in moving parts. (CPSC7.2, 8.1)
Hanggrips are between 0.95" and 1.55" in diameter. (CPSC 10.2.1) ?ootings for equipment
are stable and buried below ground level or covered by surfacing materials, (CPSC 9.7)
Equipment is free of any litter or debris (CSPC 7.2)
Compliant 12.1.28. Protrusions: (CPSC 3.2, ASTM 6.3). No components fail protrusion test. Nuts, bolts
and screws are recessed, covered or sanded smooth and level.
Compliant 12.1.29. Is shade provided over the playground area*
ParkPro Tek
Page 73 of 80

Page 74

N/A 12.1.30. The height of transfer platforms is between 11"-18"
12.2: Age / Size Appropriateness Design
Compliant 12.2.1. The play area has signs that inform users of intended user age group. (CPSC 2.2.6).
KDISCLOSURE- Stickers on the unit in place of the sign are acceptable but can be easily
removed which is why permanent signs are recommendedK
12.3: Climbing Equipment
Recommended 12.3.1. ?lexible access equipment anchoring devices are below the base of the minimum
required depth of the protective surface. (CPSC 12.1.3, ASTM 7.2.2.2)
Compliant 12.3.2. Handrails and handholds stay in place when grasped.
12.4: Playground Protective Surface
ParkPro Tek
Page 74 of 80

Page 75

Non-Compliant 12.4.1. All elevated play equipment (slides, swings, bridges, seesaws, climbing apparatus,
etc.) has proper depth of impact-absorbing material underneath the structure. Refer to
CPSC and ASTM ?1487-07 and ASTM 1292-04 for speci&cations on conforming protective
surface type, critical fall heights and how far surfacing should extend from structure.
PARYPRO TEY CANNOT GUARANTEE SUR?ACING IS COMPLIANT WITHOUT SUR?ACE
IMPACT TESTING WHICH IS HIGHLK RECOMMENDED ?OR EVERK SITE
This is a priority Two issue. (Non-compliant safety concern that may result in temporary disability.
Condition should be corrected as soon as possible.)
Wurfacing at 3.5"
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
Recommended 12.4.2. Surfaces are inspected at least monthly and raked to prevent them from becoming
packed down and to remove hidden hazards (e.g. littler, sharp objects, animal feces).
Compliant 12.4.3. Standing water is not found within any of the use zones.
Compliant 12.4.4. ?or Equipment installed after 1995, manufacturers sign attached to equipment
stating equipment must be installed over impact absorbing surface . (ASTM 14.4.1.3)
12.5: Use Zone
Compliant 12.5.1. The use zone for stationary play equipment shall extend no less than 72 in. (1830 mm)
from all sides of the play structure.
Compliant 12.5.2. There shall be a use zone for each play structure which shall consist of obstacle-free
surfacing that conforms to Speci&cation ?1292 appropriate for the fall height of the
equipment.
12.6: Swings
Compliant 12.6.1. Hardware is compliant with no issues present.
ParkPro Tek
Page 75 of 80

Page 76

Compliant 12.6.2. Swing hangers are spaced wider than seats, not less than 20. ( ASTM 8.6.1.5)
Compliant 12.6.3. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Non-Compliant 12.6.4. Swing surfacing is in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
Bero under swings
Non-Compliant 12.6.5. Swing seats are in good condition.
This is a priority Three issue. (Non-compliant safety concern that is likely to cause a minor (non-disabling) injury.
Condition should be corrected when time permits.)
Lissing safety strap
Compliant 12.6.6. Swing hangers are spaced wider than seats, not less than 20". ( ASTM 8.6.1.5)
ParkPro Tek
Page 76 of 80

Page 77

Compliant 12.6.7. Vertical distance is at least 16" between underside of occupied seat and protective
surface. (5-12 equipment-ASTM 8.6.2.5)
N/A 12.6.8. Vertical distance is at least 12" between underside of occupied seat and protective
surface (2-5 Equipment-ASTM 8.6.2.5)
Compliant 12.6.9. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Compliant 12.6.10. Swings are located away from circulation paths (a distance at least equal to the
equipment use zone and an additional safety factor for circulation, with this area free of
any obstructions) and near the periphery of the playground.
13: Playground Area - Anderson Mill Pond Park
13.1: Swings
Recommended 13.1.11. Hardware is compliant with no issues present.
handicap seat has no safety belt.
Compliant 13.1.12. Swing hangers are spaced wider than seats, not less than 20. ( ASTM 8.6.1.5)
Compliant 13.1.13. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Non-Compliant 13.1.14. Swing surfacing is in good condition.
This is a priority One issue. (Non-compliant safety concern that may result in permanent disability, loss of life or body
part.
Condition should be corrected immediately.)
0oose Mll at 5"
CPSC - 2.4.2.2 - Loose-Rll material is not an adequate depth and should be reRlled to remain compliant
CPSC - 2.4 - The surfacing under and around playground equipment is one of the most important factors
in reducing the likelihood of life-threatening head in/uries
ParkPro Tek
Page 77 of 80

Page 78

Recommended 13.1.15. Swing seats are in good condition.
Lissing safety strap
Compliant 13.1.16. Swing hangers are spaced wider than seats, not less than 20". ( ASTM 8.6.1.5)
Compliant 13.1.17. Vertical distance is at least 16" between underside of occupied seat and protective
surface. (5-12 equipment-ASTM 8.6.2.5)
N/A 13.1.18. Vertical distance is at least 12" between underside of occupied seat and protective
surface (2-5 Equipment-ASTM 8.6.2.5)
Compliant 13.1.19. There are no open "S" hooks (openings greater than or equal to 0.04"). CPSC 5.3.8.1
Compliant 13.1.20. Swings are located away from circulation paths (a distance at least equal to the
equipment use zone and an additional safety factor for circulation, with this area free of
any obstructions) and near the periphery of the playground.
ParkPro Tek
Page 78 of 80

Page 79

Summary
1.1.3 )P4': Playground is at 192D
1.1.10 )P3': Non-compliant hardware on blue slide
1.1.11 )P2': xusting and peeling decks( missing equipment( missing caps
1.3.1 )P1': "amaged rubber( loose Rll at 35
1.8.1 )P1': Missing and incorrectly installed hardware.
1.8.4 )P1': Loose Rll at 05 in many locations
1.8.7 )P1': "amaged and missing hardware. Installed incorrectly creating entanglement
2.1.13 )P2': 825
2.1.21 )P3': Pinch points on rubber ZeH climber. Missing equipment.
2.3.1 )P1': Loose Rll at 2.A75. xubber surfacing has missing sections
2.6.1 )P2': "amaged sharp edges
2.6.4 )P1': xubber damaged. Loose Rll at 45
2.6.7 )P3': jucket seats have rust and sharp edges
2.8.1 )P1': Tree in use zone. Needs to be 13D. Only at 8D
6.4.1 )P1': xubber damaged. Loose Rll at 35
6.A.1 )P1': Bangers showing signs of eHtreme wear and needs replacement.
6.A.4 )P1': Loose Rll ranges from 2-45 and rubber has cracks
A.1.7 )P3': xoad at 177D
A.3.2 )P3': Pinch points on rubber ZeH climber
A.4.1 )P2': xubber damaged. Loose Rll at 75
A.6.6 )P1': EHtreme wear on hangers and need replacement
A.6.12 )P1': Loose Rll at 3.A75. xubber surfacing has missing sections
A.6.14 )P1': Missing seat
A.6.16 )P3': Chains too close together
8.1.13 )P2': Loose equipment. jroken bubble panel. xusted deck eHposing metal.
8.1.16 )P3': Transfer station at 215
8.3.2 )P3': Loose equipment
8.4.1 )P1': Loose Rll at 05 in many locations
8.7.3 )P2': Slide height at 225
8.6.4 )P1': Surfacing is at zero in many locations.
8.6.7 )P2': jelt seats have sharp metal. Need replacement.
9.1.13 )P3': "amaged rope needs replacement.
9.4.1 )P1': Surfacing at 35
9.7.3 )P2': Connected slide is at 205
10.1.7 )P2': Playground less than 100D from road.
10.1.12 )P1': Entanglement and entrapment hazards on both stairs. xailing has an entrapment hazard.
10.1.13 )P1': joth sets of stairs show minimal support and are loose. Play feature is not set in ground.
"amaged,loose pole.
10.4.4 )P1': xailing is in the use zone of the slides.
12.4.1 )P2': Surfacing at 3.75
12.6.4 )P1': Bero under swings
12.6.7 )P3': Missing safety strap
13.1.14 )P1': Loose Rll at 75
ParkPro Tek
Page 79 of 80

Page 80

Notes
Anderson mill west
Wasp Nest in gazebo
?itness track bridge is showing signs of degradation. Railing is pulling away and should be
addressed.
Thank you for choosing ParkPro Tek for all your inspection and maintenance needs. Please
review the report for all recommended and non-compliant items.
ParkPro Tek
Page 80 of 80